Rinzwind k 26 If you do need too loosen the connectors around the back keep an eye on how they are located so that you can put them back in the same way. If you are careful it is not necessary to remove the board completely. If you have any questions or remarks please email us at termination chipmunk. Also note that the diode D1 and the fuse F1 are present.

Uploader: Dara
Date Added: 21 January 2009
File Size: 5.20 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 18522
Price: Free* [*Free Regsitration Required]

So why is all this a problem? Somewhere along the cable the signal could not be read properly because one sees not only the signal itself but also a weaker and slightly delayed reflection. The other resistor pulls the signal down towards the ground. Sign up using Facebook. Now that you so I hope at least understand that you want you scanner to be a good boy and supply some Terminator Power for that poor little terminator you will want to know how to fix the problem.

Without a terminator the signal would reflect right off the end of the cable and ‘bounce’ back.

Scaner detailled information take a look at sane-umax-doc. The normal user then mutters some nasty things about SCSI bus ‘black magic’, he or she will swap a few cables and devices around, and with a bit of astea luck a device that does supply the Termination Power moves closer to the scanner or a cable that does not have the extra wire moves further away from the scanner and the problem will go away.


UMAX Astra P – Flatbed scanner – Letter – dpi x dpi – parallel – Video Dailymotion

Want to receive updates about upcoming auctions? I tried reading different information on installing the package, but frankly i was not able to do any thing. If the signal is high the lower resistor will ‘pull’ extra hard, and if the signal is low the upper resistor will do its best to raise the signal. This is an electronic component that dampens reflections in the signal. If you have any questions or remarks please email us at termination chipmunk.

Their response is that they see no problem.

It will be hard or even impossible for someone to ‘read’ your message because the data you are sending is polluted by this reflection. So astrra do I fix this mess?

Umax Astra 600S Flatbed Scanner

The following factors may prevent the notifications from being sent on time or at all: If this is not the case the terminator can not work properly and in fact if it is only connected to one of the two it will be worse than having no terminator at all.

By using our site, you acknowledge that you have read and astfa our Cookie PolicyPrivacy Policyand our Terms of Service.

This will usually be OK but sometimes there will be trouble. Hold the other end and pull the line tight. S6, S12, Astra s, Astra s ans probably a few more.


UMAX AstraSlim 600 Free Driver Download

These two forces combined pull the signal toward the middle and damp the signal. I suggest you hold one hand on the power-button of the scanner while umax astra s scanner try the first scans! I am a windows user and life till date was very simple, just click a button and its all done.

This involve removing a few screws. Bidders shall rely upon their own inspections of the property and not upon any representations or descriptions of the Dakil Auctioneers, Inc. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Sign up using Facebook.

We have notified UMAX of this fact and that we see asrra as an important problem. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Browse All Upcoming Auctions Have any questions about this item?

Rinzwind k 26 All pre-bidding will end at A full invoice should be emailed to the winner by the auctioneer within a day or two. Surprisingly enough UMAX has almost taken care of this for you.